進口通風蝶閥德國洛克進口品牌

進口通風蝶閥結構特點：

1.采用中線式碟板與短結構鋼板焊接的新型結構形式設計制造的，結構緊湊、重量輕、便于安裝、流阻小、流通量大，避免高溫膨脹的影響，操作輕便。

2.內無連桿、螺栓等、工作可靠、使用壽命長?？梢远喙の话惭b，不受介質流向影響。

進口通風蝶閥規格參數： 

Specification parameters of inlet ventilation butterfly valve:
Product name：Inlet ventilation butterfly valve
Product model：DE LOCKE
Driving mode：Pneumatic, electric, manual, worm gear
Connection form：Butt clamp, flange, welding
Applicable temperature：-40℃ ~ +800℃
Sealing structure：Soft seal
Pressure range：0.1-10Mpa
Nominal diameter：DN40-2000
Common materials：Cast steel, 304316l, alloy steel, etc
                                                                                                                                                                  

進口通風蝶閥產品簡介：

德國洛克《DE LOCKE》進口通風蝶閥采用與閥體相同材料加工成密封圈，其適用溫度隨閥體選材而定，公稱壓力≤0.6MP工，一般適用工業、冶金、環保等管道作通風調節介質流量之用。蝶閥的啟閉件是用圓形蝶板作啟閉件并隨閥桿轉動來開啟、關閉和調節流體通道的一種閥門。蝶閥的蝶板安裝于管道的直徑方向。在蝶閥閥體圓柱形通道內，圓盤形蝶板繞著軸線旋轉，旋轉角度為0°~90°之間，旋轉到90°時，閥門則牌全開狀態。

Introduction to imported ventilation butterfly valve products:
The imported ventilation butterfly valve of de lock in Germany is processed into sealing ring with the same material as the valve body. Its applicable temperature is determined by the material selection of valve body, and the nominal pressure is less than 0.6mp. It is generally applicable to industrial, metallurgical, environmental protection and other pipelines for ventilation and medium flow regulation. The opening and closing parts of butterfly valve are a kind of valve which uses circular butterfly plate as the opening and closing parts and turns with the stem to open, close and adjust the fluid passage. Butterfly plate of butterfly valve is installed in diameter direction of pipeline. In the cylindrical channel of butterfly valve body, the disc butterfly plate rotates around the axis, and the rotation angle is between 0 ° and 90 ° and the valve plate is fully open when it is rotated to 90 °.
 

進口通風蝶閥安裝與維護：

1、安裝位置、高度、進出口方向必須符合設計要求，注意介質流動的方向應與閥體所標箭頭方向，連接應牢固緊密。

2、閥門安裝前必須進行外觀檢查，閥門的銘牌應符合現行國家標準《通用閥門標志》GB 12220的規定。對于工作壓力大于1.0 MPa 及在主干管上起到切斷作用的閥門，安裝前應進行強度和嚴密性能試驗，合格后方準使用。強度試驗時，試驗壓力為公稱壓力的1.5倍，持續時間不少于5min，閥門殼體、填料應無滲漏為合格。嚴密性試驗時，試驗壓力為公稱壓力的1.1倍；試驗持續的時間符合GB 50243要求。

Installation and maintenance of inlet ventilation butterfly valve:
1. Installation position, height and direction of inlet and outlet must meet the design requirements. Note that the direction of medium flow shall be in the direction of arrow marked by the valve body, and the connection shall be firm and tight.
2. Before the valve is installed, the appearance inspection must be carried out. The nameplate of the valve shall conform to the current national standard general valve mark GB 12220. For valves with working pressure greater than 1.0MPa and acting as a cutoff on the main pipe, strength and tightness performance test shall be conducted before installation, and only after passing the test. During strength test, the test pressure is 1.5 times of nominal pressure, and the duration is not less than 5min. It is qualified that the valve shell and packing should be free of leakage. When the tightness test is conducted, the test pressure is 1.1 times of the nominal pressure; the test duration meets the requirements of GB 50243.
                                                                               

進口通風蝶閥訂貨須知：

A、若訂貨前還未選定型號，請向我們提供您的使用參數:

1.公稱通徑 2.產品型號