進口真空球閥德國洛克各種參數以及說明

進口真空球閥結構特點:

A.手動真空球閥密封結構設計獨特，漏率可達到＜1×10-10Pa.M3/S,改變了球閥不能滿足高真空、超高真空的現狀；

B.真空球閥開關扭矩小，配置氣動執行器小，工作穩定、可靠；

C.真空球閥結構緊湊，重量輕，外形簡潔、美觀；

D.該閥既能適用高真空，又能適用一定的正壓力下使用；

 

進口真空球閥規格參數：

1.漏率：閥體 ≤1.3×10-9Pa.M3/S；

2.壓力范圍：1.3×10-7Pa～6×105Pa；

3.工作介質：水、蒸氣、酸、堿。

4.規格范圍：DN10-50mm

6.壓力范圍：1.0-6.4Mpa

5.工作溫度：-30℃～+150℃。

6.安裝位置：任意。

7.壽命：≥5萬次。

Specifications and parameters of imported vacuum ball valve:
1. Leakage rate: valve body ≤ 1.3 × 10-9pa.m3/s;
2. Pressure range: 1.3 × 10-7pa ~ 6 × 105Pa;
3. Working medium: water, steam, acid and alkali.
4. Specification range: DN 10-50 mm
6. Pressure range: 1.0-6.4mpa
5. Working temperature: - 30 ℃ ~ + 150 ℃.
6. Installation position: arbitrary.
7. Service life: ≥ 50000 times.

進口真空球閥在真空系統中的作用：

1.開關氣路，當閥1和閥4關閉，閥2打開時，機械真空泵Ⅲ對容器I抽真空，氣流流經預真空抽氣管路；當閥2關閉，閥4打開時，機械泵可單獨對擴散泵抽真空；當閥1和閥4同時打開時，擴散泵和機械泵可同時工作，對容器進行抽空，此時氣流流經擴散泵?？梢?，閥門在這種操作中的作用是開關氣路，改變氣流的流經路線。

2.控制氣流大小，調節真空度在圖1中，調節閥1的閥蓋開啟角度，即可調節流經管路的氣流量大小；關閉閥2和閥4，通過放氣閥3可以給機械泵Ⅲ的入口放成大氣；通過放氣閥5可以調節容器內的真空度。

3.定量充氣，在玻璃閥的柱塞上有個一定體積的小洞，當小洞轉向右邊和高壓氣瓶連通時，小洞中就可充滿高壓氣體；當它轉向左邊和真空容器連通時，就把該體積的高壓氣體放進容器中去，這樣就起到了定量充氣的作用。

Function of imported vacuum ball valve in vacuum system:
1. Switch the gas path. When valve 1 and valve 4 are closed and valve 2 is open, mechanical vacuum pump III vacuumizes the container I, and the air flows through the pre vacuum pumping pipeline. When valve 2 is closed and valve 4 is open, the mechanical pump can vacuum the diffusion pump alone. When valve 1 and valve 4 are opened at the same time, the diffusion pump and mechanical pump can work at the same time to empty the container, and the air flows through the diffusion pump. It can be seen that the role of the valve in this operation is to switch the gas path and change the flow path of the air.
2. Control the air flow and adjust the vacuum degree. In Figure 1, adjust the opening angle of the valve cover of valve 1 to adjust the air flow through the pipeline; close valve 2 and valve 4 to release the air to the inlet of mechanical pump III through vent valve 3; adjust the vacuum degree in the container through vent valve 5.
3. Quantitative inflation: there is a certain volume of small hole on the plunger of the glass valve. When the small hole turns to the right to connect with the high-pressure cylinder, the small hole can be filled with high-pressure gas; when it turns to the left to connect with the vacuum container, the volume of high-pressure gas is put into the container, which plays the role of quantitative inflation.
 

進口真空球閥產品簡介:

德國洛克《DE LOCKE》進口真空球閥是指工作壓力低于標準大氣壓的，即處于真空負壓的狀態，形成一定真空的球閥，所以通常也被稱為真空負壓球閥，主要用于真空系統中做開關控制或調節流量使用。

進口真空球閥適用于真空系統中接通或切斷管路的介質流。真空球閥為直通式手動球閥，靠球面密封，因而既能用在真空狀態下，也能在低壓狀態下使用，并可任意位置安裝。適用真空范圍：0.6*10~1.3*10pa。

Introduction of imported vacuum ball valve products:
German Locke "de Locke" imported vacuum ball valve refers to the working pressure is lower than the standard atmospheric pressure, that is, in the state of vacuum negative pressure, forming a certain vacuum ball valve, so it is usually called vacuum negative pressure ball valve, mainly used for switch control or flow regulation in vacuum system.
The imported vacuum ball valve is suitable for connecting or cutting off the medium flow of pipeline in vacuum system. The vacuum ball valve is a straight through manual ball valve, which is sealed by spherical surface. Therefore, it can be used in both vacuum state and low pressure state, and can be installed at any position. Applicable vacuum range: 0.6 * 10 ~ 1.3 * 10Pa.
 

進口真空球閥訂貨須知：

A、若訂貨前還未選定型號，請向我們提供您的使用參數:

1.公稱通徑 2.產品型號 3.流體性質（包括公稱壓力、溫度、介質） 4.閥體、密封材料 5.連接方式

B、若已經由設計單位選定我公司的產品型號，請按型號直接向我司銷售部訂購

C、當使用的場合非常重要或管路比較復雜時，請您盡量提供設計圖紙和詳細參

數，由我們德國洛克閥門技術員為您審核把關。

D、感謝您訪問我公司的網站〖〗，如有任何疑問.

您可以致電給我們《》我們一定會盡心盡力為您提供優質的服務!