進口不銹鋼截止閥品牌廠家-德國洛克

 

進口不銹鋼截止閥結構特點：

1、密封面不易磨損、擦傷密封性較好，壽命較長；

2、結構較簡單，造型美觀，工藝加工先進；

3、啟閉時閥瓣行程較小，啟閉時間較短，閥門高度較?。?/span>

4、閥蓋上設計了上密封座，在全開狀態下使填料密封更為可靠。

                                                                                 

進口不銹鋼截止閥規格參數：

A、閥體材料：WCB、304、316

B、閥門口徑：DN15-300

C、閥門壓力：PN16-PN100

D、連接標準：ASME B16.10、DIN2501

E、控制方式：手動、電動、氣動

F、密封材料：304

G、工作溫度：-20℃至+150℃ (特殊定做+550°)

                                                                                    

進口不銹鋼截止閥工作原理：

①閥瓣、閥座密封面采用鐵基合金堆焊或司太立鈷基硬質合金堆焊而成，耐磨、耐高溫、耐腐蝕、抗擦傷性能好，使用壽命長;

②閥桿經調質及表面氮化處理，有良好的抗腐蝕性和抗擦傷性;

③可采用各種配管法蘭標準及法蘭密封面型式，滿足各種工程需要及用戶要求;

④閥體材料品種齊全，填料、墊片可根據實際工況或用戶要求合理選配，能適用于各種壓力、溫度及介質工況;

⑤倒密封采用螺紋連接密封座或本體堆焊奧氏體不銹鋼而成，密封可靠，更換填料可在不停機情況下進行，方便快捷，不影響系統運行。

Working principle of imported stainless steel globe valve:
① The sealing surface of valve disc and valve seat is overlaid with iron-based alloy or Stellite cobalt based cemented carbide, with good wear resistance, high temperature resistance, corrosion resistance and abrasion resistance, and long service life;
② After quenching and tempering and surface nitriding treatment, the valve stem has good corrosion resistance and scratch resistance;
③ All kinds of piping flange standards and flange sealing surface types can be adopted to meet various engineering needs and user requirements;
④ The valve body has a wide range of materials, and the packing and gasket can be reasonably selected according to the actual working conditions or user's requirements, which can be applied to various pressure, temperature and medium working conditions;
⑤ The inverted seal is made of thread connection seal seat or body overlaid with austenitic stainless steel. The seal is reliable. The replacement of packing can be carried out without stopping the machine. It is convenient and fast, and does not affect the operation of the system.
        

進口不銹鋼截止閥產品簡介：

進口不銹鋼截止閥的啟閉件是塞形的閥瓣，密封面呈平面或錐面，閥瓣沿流體的中心線作直線運動。閥桿的運動形式，有升降桿式（閥桿升降，手輪不升降），也有升降旋轉桿式（手輪與閥桿一起旋轉升降，螺母設在閥體上）。截止閥只適用于全開和全關，不允許作調節和節流。

Introduction of imported stainless steel globe valve products:
The opening and closing parts of imported stainless steel globe valve are plug-shaped disc, the sealing surface is plane or cone, and the disc moves linearly along the center line of fluid. The movement forms of the valve stem include the lifting rod type (the valve stem rises and falls, but the hand wheel does not rise and falls), and the lifting rotary rod type (the hand wheel and the valve stem rise and fall together, and the nut is set on the valve body). Stop valve is only suitable for full open and full close, not allowed to adjust and throttle.
                                                                       

進口不銹鋼截止閥施工、安裝要點：

1、安裝位置、高度、進出口方向必須符合設計要求，連接應牢固緊密。

2、安裝在保溫管道上的各類手動閥門，手柄均不得向下。

3、安裝前必須進行外觀檢查，閥門的銘牌應符合現行國家標準《通用閥門標志》GB 12220的規定。對于工作壓力大于1.0 MPa 及在主干管上起到切斷作用的閥門，安裝前應進行強度和嚴密性能試驗，合格后方準使用。強度試驗的試驗壓力為公稱壓力的1.5倍，持續時間不少于5min，閥門殼體、填料應無滲漏為合格。嚴密性試驗的試驗壓力為公稱壓力的1.1倍；試驗壓力在試驗持續的時間應符合GB 50243標準要求，以閥瓣密封面無滲漏為合格。

4、手輪、手柄及傳動機構，不允許作起吊用。

5、介質的流向應與閥體所示箭頭方向一致。

Key points of construction and installation of imported stainless steel stop valve:
1. The installation position, height, inlet and outlet direction must meet the design requirements, and the connection should be firm and tight.
2. The handle of all kinds of manual valves installed on the insulation pipeline shall not be downward.
3. Visual inspection must be carried out before installation, and the valve name plate shall comply with the current national standard "general valve marks" GB 12220. For the valve with working pressure greater than 1.0 MPa and cut-off function on the main pipe, the strength and tightness test shall be conducted before installation, and the valve can only be used after it is qualified. The test pressure of strength test shall be 1.5 times of the nominal pressure, and the duration shall not be less than 5min. The valve shell and packing shall be qualified if there is no leakage. The test pressure of the tightness test is 1.1 times of the nominal pressure; the duration of the test pressure shall meet the requirements of GB 50243, and the valve disc sealing surface is qualified if there is no leakage.
4. Hand wheel, handle and transmission mechanism are not allowed for lifting.
5. The flow direction of the medium shall be consistent with the arrow direction shown on the valve body.
                                                                               

進口不銹鋼截止閥訂貨須知：

A、若訂貨前還未選定型號，請向我們提供您的使用參數:

1.公稱通徑 2.產品型號 3.流體性質（包括公稱壓力、溫度、介質） 4.閥體、密封材料 5.連接方式

B、若已經由設計單位選定我公司的產品型號，請按型號直接向我司銷售部訂購

C、當使用的場合非常重要或管路比較復雜時，請您盡量提供設計圖紙和詳細參

數，由我們德國洛克閥門技術員為您審核把關。

D、感謝您訪問我公司的網站〖〗，如有任何疑問.

您可以致電給我們《》我們一定會盡心盡力為您提供優質的服務!