進口水用減壓閥德國洛克品牌產品介紹

進口水用減壓閥結構特點:

具有動作靈敏、快捷、性能可靠、使部附有過濾網，便于整體安裝，避免雜物堵塞，使其更加安全可靠?？伤交虼怪卑惭b于給水、消防系統及其他清水系統中。

在一定流量范圍內可控制該閥出口壓力為相對固定值。膜片的設計采用了特殊的形狀，旨在保證下游用水壓力波動時減壓的準確性。同時它能抗擊壓力瞬間的變化，耐老化，延長了減壓閥的使用壽命。

進口水用減壓閥規格參數：

◆公稱范圍：DN40-1200mm

◆公稱壓力：PN1.0MPa-2.5MPa

◆介質溫度：O～80 ℃

◆密封等級：零泄漏

◆閥體材料：球墨鑄鐵、碳鋼、不銹鋼

◆閥瓣材料：球墨鑄鐵、碳鋼

◆閥桿材料：2Cr13

◆膜片材料：強化尼龍橡膠

◆閥瓣密封圈：橡膠或F4

◆*動作壓力：≥O.04MPa

◆緩閉時間：3～60s(可調)

◆適用介質：適用于工礦企業、高層建筑、生活用水、消防用水系統中，在需要減靜壓和動壓的場合可以取代中間水箱，節約建筑中間水箱的費用，擴大建筑物使用的空間。

進口水用減壓閥安裝說明: 

1、安裝高壓氣體減壓閥之前必須對管路系統進地沖洗清理，以防焊渣、氧化皮等臟物流入閥內，影響閥門正常工作。

2、高壓氣體減壓閥應安裝在便于操作和維修的地方，并且必須直立安裝在水平管路上(見安裝示意圖)應注意使管路中介質的流向與閥體上箭頭所示方向一致，切勿裝反

3、高壓氣體減壓閥在安裝使用時，應先把旁通管路上的截止閥打開，排除管路中的冷凝水和汽水混合物，以防減壓閥開啟時產生水擊現象損壞減壓閥，當無異?，F(xiàn)象后，按順時針方向緩慢旋轉調節螺釘，將出口壓力調至所需要的壓力(以閥后表壓為準)，調整好后，將鎖緊螺母鎖緊，擰上防護罩。

4、減壓閥前應安裝過濾器，以防止介質中的雜質進入減壓閥，影響其性能。

5、安裝的減壓閥前后應有一段直管，閥前直管長度約為600毫米，閥后直管長度約為1000毫米。

Installation instructions for pressure reducing valve for imported water:
1. Before installing the high-pressure gas pressure reducing valve, the pipeline system must be washed and cleaned to prevent the dirty flow of welding slag, oxide skin and other dirt into the valve, which will affect the normal operation of the valve.
2. The high pressure gas pressure reducing valve shall be installed in a place convenient for operation and maintenance, and it must be installed on the horizontal pipeline (see installation diagram). Pay attention to make the flow direction of medium in the pipeline consistent with the direction shown by arrow on the valve body, and do not install reverse
3. When the high pressure gas pressure reducing valve is installed and used, the stop valve on the bypass pipeline should be opened first to remove the condensate water and steam water mixture in the pipeline, so as to prevent water hammer from damaging the pressure reducing valve when the pressure reducing valve is opened. When there is no abnormal phenomenon, slowly rotate the adjusting screw clockwise to adjust the outlet pressure to the required pressure (based on the gauge pressure behind the valve). After the adjustment, the outlet pressure should be adjusted, Lock the lock nut and screw on the protective cover.
4. A filter should be installed before the pressure reducing valve to prevent impurities in the medium from entering the pressure reducing valve and affecting its performance.
5. There should be a straight pipe before and after the pressure reducing valve. The length of the straight pipe in front of the valve is about 600mm, and the length of the straight pipe behind the valve is about 1000mm.
 

進口水用減壓閥產品簡介:

德國洛克《DE LOCKE》進口水用高壓減壓閥，Water high-pressure reducing valve也叫高壓調壓閥，主要由調節彈簧、膜片、活塞、閥座、閥瓣等零件組成，利用膜片直接傳感下游壓力驅動閥瓣，控制閥瓣開度完成減壓穩壓功能的閥門。較高閥前壓力32Mpa，出口減到0.1Mpa，適用于高壓或者高壓差的水流介質場合，將進口的高壓力減到并穩定在需要的壓力值。

Introduction to the products of pressure reducing valve for imported water:
The high pressure reducing valve for imported water of Locke, Germany, is also called high pressure reducing valve. It is mainly composed of adjusting spring, diaphragm, piston, valve seat, disc and other parts. The valve is directly driven by downstream pressure by diaphragm, and the valve disc opening is controlled to complete the function of pressure reduction and pressure regulation. The pressure in front of the higher valve is 32Mpa, and the outlet is reduced to 0.1MPa. It is suitable for the high pressure or high pressure difference water flow medium, and the high pressure at the inlet is reduced to and stabilized at the required pressure value.