德國洛克供應優質進口背壓閥

一、進口背壓閥描述：

德國LOCKE洛克進口背壓閥又稱背壓調節器是通過內置彈簧的彈力來實現動作：當系統壓力比設定壓力小時，工作閥門膜片在彈簧彈力的作用下堵塞管路；當系統壓力比設定壓力大時，膜片壓縮彈簧，管路接通，液體通過背壓閥。背壓閥結構同單向閥相似，但開啟壓力大于單向閥，在0.2到1.6兆帕間。在管路或是設備容器壓力不穩的狀態下，背壓閥能保持管路所需壓力。另在泵的出端由于重力或其它作用常會出現虹吸現象，此時背壓閥能消減由于虹吸產生的流量及壓力的波動。而對于計量泵等容積泵在低系統壓力下工作時，都會出現過量輸送。為防止類似問題，必須使計量泵的出口至少有0.7Bar的背壓，一般通過在計量泵出口安裝背壓閥來達到目的。

German lock lock import back pressure valve, also known as back pressure regulator, is operated by the spring force inside: when the system pressure is smaller than the set pressure, the working valve diaphragm blocks the pipeline under the spring force; when the system pressure is larger than the set pressure, the diaphragm compresses the spring, the pipeline is connected, and the liquid passes through the back pressure valve. The structure of the back pressure valve is similar to that of the check valve, but the opening pressure is greater than that of the check valve, between 0.2 and 1.6 MPa. When the pressure of pipeline or equipment vessel is unstable, the back pressure valve can maintain the required pressure of pipeline. In addition, siphon often occurs at the outlet of the pump due to gravity or other effects. At this time, the back pressure valve can reduce the flow and pressure fluctuation caused by siphon. For metering pumps and other positive displacement pumps in the low system pressure, there will be excessive delivery. In order to prevent similar problems, the outlet of the metering pump must have a back pressure of at least 0.7bar, which is generally achieved by installing a back pressure valve at the outlet of the metering pump.

二、進口背壓閥技術參數：

316L 不銹鋼,銅,Monel,Hastelly合金和鈦材可以選擇

電解拋光本體達到25 Ra的光潔度

切斷操作

Cv值:0.2

使用溫度: -40° to 500° F (-40° to +260° C)

控制壓力范圍是 10,25,50,100,250,500, 750和1000 PSIG

極限壓力是 2 倍的最大的工作壓力

爆破壓力是 4 倍的最大的工作壓力

僅重1.9 磅 (0.86 公斤)

鑲嵌式安裝或面板安裝

316L stainless steel, copper, Monel, hastelly alloy and titanium can be selected

Electropolishing body to 25 RA finish

Cut off operation

CV value: 0.2

Service temperature: - 40 ° to 500 ° f (- 40 ° to + 260 ° C)

The control pressure range is 10,25,50100250500, 750 and 1000 psig

The limit pressure is twice the maximum working pressure

The burst pressure is 4 times the maximum working pressure

Weighs only 1.9 lbs (0.86 kg)

Mosaic installation or panel installation

三、進口背壓閥工作原理：

流體從背壓閥進口進入，被膜片阻擋，于是流體對膜片產生向上的壓力。當壓力足夠大時，彈簧被壓縮，流體頂起膜片形成通道，從背壓閥出口流出；若流體壓力不夠，就會形成憋壓，使進口壓力上升直到達到額定壓力，頂起膜片形成通路。

背壓閥的額定壓力可調節，一般通過調節彈簧上端的頂桿，從而調節彈簧的長度來實現

The fluid enters from the inlet of the back pressure valve and is blocked by the diaphragm, so the fluid produces upward pressure on the diaphragm. When the pressure is large enough, the spring will be compressed, and the fluid will jack up the diaphragm to form a channel and flow out from the outlet of the back pressure valve; if the fluid pressure is not enough, it will form pressure holding, so that the inlet pressure will rise until it reaches the rated pressure, and jack up the diaphragm to form a channel.

The rated pressure of the back pressure valve can be adjusted, which is generally realized by adjusting the top bar at the upper end of the spring, so as to adjust the length of the spring