找商網手機端：m.zhaosw.com
深圳市凱士比閥門有限公司
主營產品： 機械設備, 閥門, 水泵, 五金交電, 機電設備
䀋䀐䀌䀏䀋䀒䀐䀏䀓䀒䀏
收藏 
進口高揚程自吸泵-德國HANK原裝品牌家用大流量單相農用高揚程自吸泵廠家
價格
訂貨量(臺)
￥3600.00
≥1
￥3500.00
≥10
店鋪主推品 熱銷潛力款
聯系人 方同 經理
䀋䀐䀌䀏䀋䀒䀐䀏䀓䀒䀏
發貨地 廣東省深圳市
在線客服
深圳市凱士比閥門有限公司
店齡5年 
企業認證
聯系人
方同 經理
聯系電話
䀋䀐䀌䀏䀋䀒䀐䀏䀓䀒䀏
經營模式
生產廠家
所在地區
廣東省深圳市
主營產品
進入店鋪
收藏本店
商品參數
|
商品介紹
|
聯系方式
訂貨號 SKU61006
品牌 德國HANK
貨號 61006
型號 61006
材質 不銹鋼
驅動方式 電動
用途 自吸
泵軸位置 臥式
葉輪結構 半開式葉輪
葉輪數目 單級
葉輪吸入方式 單吸式
原理 單吸式
性能 高揚程
輸送介質 工業污水
揚程 10-80m
商品介紹
進口高揚程自吸泵解決了單吸式自吸泵的軸向拉力大、自吸時間長、效率低等問題，具有吸程高、自吸時間短、使用效率高、節能效果顯著、運行平穩，使用壽命長等優點。集自吸和無堵塞排污于一體，采用軸向回流外混式，并通過泵體、葉輪流道的獨特設計，既不需要安裝底閥和灌引水，又可吸排含有顆粒固體和纖維等
使用范圍：
環境溫度≤50℃，介質溫度≤80℃，特殊要求溫度可達200℃。
介質PH值鑄鐵材質為6-9，不銹鋼為2-13.
介質中毒不超過1240kg/m3
自吸高度不能超過規定值5-7米，吸入管長度為≤10m。
污水型通過能力懸浮顆粒直徑約為泵口徑的20%，纖維長度約為泵口徑的5倍。
安裝要求：
1、整套水泵運抵現場時，都已裝好電機，找平底座時，可不必卸下水泵和電機
2、將底座放在地基上，準備找平后填充混凝土之用。
3、用水平儀利用泵的吐出口平面檢查底座的水平度，找平后，安上地腳螺栓，用混凝土灌注地腳螺栓。
4、將鋼尺放在聯軸器上（上、下、前、后測量），檢查泵與電機的軸心線是否重合。
5、待固定地腳螺栓的混凝土完全干固后，擰緊地腳螺栓的螺母，后再檢查一下整臺機組的水平度，稍有不平時，可用楔鐵找平。
6、安裝吸水和出口管路，當管路與泵結合時，應注意勿使管路的重量和壓力增加到泵上，以免泵出現變形。
保養要求：
1、自吸泵保養與清洗前確保所接的電源要關閉，將殘留泵體內的液體排放感覺，并將出入口凡而關閉，維修人員應穿著防護衣及防護面罩，安全鞋和襪子
2、定期檢查出入扣，防止異物阻塞泵體而造成馬達空轉，燒壞泵浦。
3、馬達與泵浦結合，必須校正準確，使馬達與泵浦在同一直線。
4、軸封護罩固定在后軸封上，當后封蓋鎖緊在腳座上時，必須在泵的正中心。
5、葉輪固定螺絲以順時針方向?qū)⑷~輪鎖緊，葉輪與中封蓋之間的縫隙約1-1.5MM，縫隙大小會將葉輪磨損
產品特點：
1、獨特地強自吸自動控制功能，具有高吸程，快自吸，不需引灌水便能自吸起動及能自動控制，特別適用于配套在機車一體化移動泵站上，作為給排水設備，可廣泛應用于抗洪搶險、排澇、消防等場合。
2、因其快自吸，大大減少了60%的自吸時間，有效提高操作工作效率50%以上，提高了吸程高度30%以上，并使其使用壽命延長，達到了使用的耐久性、穩定性、實用性、經濟性等功能。
3、因采用獨特的雙吸自吸式真空泵組，自動控制系統的巧妙組合設計結構，在大流量、大口徑應用更廣泛，因為采用雙吸式結構，水在葉輪兩端同時進水，中間排出，沒有軸向拉力，所以流量與口徑不設上限，正?？趶皆贒N100~DN600，流量100噸~3000噸，非標無論口徑流量大小可訂做。
4、使用時不需引灌水就能正常工作，耐干磨、不需底閥，與其它產品有本質上、結構上的區別。因其具有強自吸自動控制等功能，具有高吸程，快自吸起動即能自動控制（即真空度降低到低位時真空泵組自動起動，真空度升到到高位時真空泵組自動多功能停機，不干擾主泵的運行，起輔助作用）。
5、新采用的自控引水裝置，引入了內置機械式浮球閥與監測探頭并用的新模式，大地提高了設備的可靠性，即時真空泵一直運行，水箱內的水位達到一定的位置，機械式浮球閥會因浮力而自動關閉，從而使水不能進入真空泵，對真空泵起雙重保護作用，使真空泵不會因進水而損壞部件。增加了阻水閥，裝在外接管路上，可有效阻擋水汽進入真空泵。
The high-lift self-priming pump solves the problems of high axial tension, long self-priming time and low efficiency of the single-suction self-priming pump. It has high suction head, short self-priming time, high use efficiency, significant energy saving effect, and stable operation. Long life and other advantages. It integrates self-priming and non-clogging sewage discharge, adopts axial backflow external mixing type, and has a unique design through the pump body and impeller flow path. It does not require the installation of a bottom valve and irrigation and drainage, and can suck and discharge particles containing solids and fibers.
Range of use:
Ambient temperature≤50℃, medium temperature≤80℃, special requirements temperature can reach 200℃.
Medium PH value cast iron material is 6-9, stainless steel is 2-13.
Medium poisoning does not exceed 1240kg/m3
The self-suction height cannot exceed the specified value 5-7 meters, and the suction pipe length is ≤10m.
The diameter of sewage-type passing capacity suspended particles is about 20% of the pump caliber, and the fiber length is about 5 times the pump caliber.
Installation requirements:
1. When the whole set of water pump arrives on site, the motor has been installed. When leveling the base, it is not necessary to remove the water pump and motor
2. Place the base on the foundation and prepare to fill it with concrete after leveling.
3. Check the level of the base with the level of the pump's discharge port using a spirit level. After leveling, install the anchor bolts and pour the anchor bolts with concrete.
4. Put the steel rule on the coupling (upper, lower, front and back measurement), and check whether the axis line of the pump and the motor coincide.
5. After the concrete fixing the anchor bolts is completely dry, tighten the nuts of the anchor bolts, and then check the levelness of the entire unit. If there is a little unevenness, the wedge iron can be used for leveling.
6. Install the suction and outlet pipelines. When the pipeline is combined with the pump, be careful not to increase the weight and pressure of the pipeline on the pump to avoid deformation of the pump.
Maintenance requirements:
1. Before the maintenance and cleaning of the self-priming pump, make sure that the connected power supply should be turned off, the residual liquid in the pump body should be discharged, and the entrance and exit should be closed. Maintenance personnel should wear protective clothing and protective masks, safety shoes and socks
2. Regularly check the access button to prevent the foreign body from blocking the pump body and causing the motor to run dry, which will burn the pump.
3. The combination of the motor and the pump must be corrected accurately so that the motor and the pump are in the same straight line.
4. The shaft seal shield is fixed on the rear shaft seal. When the rear cover is locked on the foot, it must be in the center of the pump.
5. The impeller fixing screw locks the impeller in a clockwise direction, the gap between the impeller and the middle cover is about 1-1.5MM, the size of the gap will wear the impeller
Features:
1. Uniquely strong self-priming automatic control function, with high suction range, fast self-priming, self-priming start and automatic control without introducing irrigation water, especially suitable for supporting on locomotive integrated mobile pumping station, as water supply and drainage The equipment can be widely used in anti-flood and emergency rescue, drainage, fire protection and other occasions.
2. Because of its fast self-priming, the self-priming time is greatly reduced by 60%, the operating efficiency is effectively improved by more than 50%, the suction height is increased by more than 30%, and its service life is extended to achieve the durability, Stability, practicality, economy and other functions.
3. Because of the unique double-suction self-priming vacuum pump set and the clever combination design structure of the automatic control system, it is more widely used in large flow and large diameter. Because of the double-suction structure, water enters at both ends of the impeller at the same time. There is no axial pulling force, so there is no upper limit on the flow rate and caliber. The normal caliber is DN100 ~ DN600, the flow rate is 100 tons ~ 3000 tons, non-standard regardless of the caliber flow size can be customized.
4. When using it, it can work normally without introducing irrigation water. It is resistant to dry grinding and does not require a bottom valve. It is essentially and structurally different from other products. Because of its strong self-priming automatic control and other functions, it has a high suction range, and it can be automatically controlled when the self-priming starts quickly (that is, the vacuum pump set starts automatically when the vacuum level drops to a low position, and the vacuum pump set automatically stops by multiple functions when the vacuum level rises to a high position. , Does not interfere with the operation of the main pump, plays an auxiliary role).
5. The newly adopted self-controlled water diversion device introduces a new mode of using a built-in mechanical float valve and a monitoring probe, which greatly improves the reliability of the equipment. The vacuum pump is always running, the water level in the water tank reaches a certain position, and the mechanical float valve It will automatically shut down due to buoyancy, so that the water can not enter the vacuum pump, and double protection for the vacuum pump, so that the vacuum pump will not damage parts due to water ingress. The water blocking valve is added and installed on the external pipeline, which can effectively block the water vapor from entering the vacuum pump.
德國漢克（HANK）進口水泵成立于1852年創建于門興格拉德巴赫（Monchengladbach）是位于德國北萊茵-威斯特法倫州首府杜塞爾多夫市以西的一座城市。于19世紀50年代初德國經濟快速發展，由于德國能源短缺，政府在節能方面加大力度，因此HANK(Trouble Less pump沒有故障的水泵)公司成立。漢克水泵是以生產高品質、先進的水泵、測量及控制系統而享譽全球的跨國性生產企業，在全球幾十個國家擁有子公司及分支機構，公司產品涉及用途：石油、化工、電力、冶金、制藥、食品、水處理、市政給排水、天然氣、造紙、電子工業、樓宇、機械設備配套等領域。
GERMANY HANK PUMP LIMITED is founded on 1852 in Monchengladbach,which is located at one city in North Rhine in Germany, which is the west of Nordrhein-Westfalen. At the beginning of 1850s, as the rapid development of economic and the shortages of energy in Germany , the government had been in saving energy aspect. On this occasion, HANK Pump (Trouble Less Pump) was established.Hank pump is the world-famous transnational production enterprise,which produces high quality and advanced pump, measurement and control system, and which has its divisions and branches in dozens of countries in the global. The company products user involves the petroleum, the chemical industry, the electric power, the metallurgy, the drugs manufacture, food, the water treatment, the municipal administration to give draining water, the natural gas, the papermaking, the electronics industry, the building, the mechanical device necessary ect..
德國漢克（HANK）水泵的價值理念概括為：責任－遠見－創新。我們因自身的責任感、遠見及專注于創造前所未有的解決方案和理念，而成為全球領先的水泵制造商。
The conclusion of the pump concept in German Hank pump is resposibility,foresight,innovation. For ourselves resposibility, foresight and focusing on creating unprecendented solution and concept,our company has become the lead of pump manufacturer in the global.
Phone: +86 (0) 755 / 83330270-400
Mobile: +86 (0) 13691839789
Fax: +86 (0)755 / 83330270 - 408
E-Mail: sales@hankchina.com、fang.tong@hankchina.com
URL:www.hankchina.com、www.ksbvalve.com
聯系方式
公司名稱 深圳市凱士比閥門有限公司
聯系賣家 方同 
（QQ：1246775303）
（QQ：1246775303） 電話 䀍䀓䀔䀔-䀌䀋䀑䀒䀍䀌䀑䀒
手機 䀋䀐䀌䀏䀋䀒䀐䀏䀓䀒䀏
傳真 䀍䀓䀔䀔-䀌䀋䀑䀒䀍䀌䀑䀒
網址 http://www.ksbvalve.com
地址 廣東省深圳市
方同 經理
䀋䀐䀌䀏䀋䀒䀐䀏䀓䀒䀏
掃碼查看 掃碼查看
手機掃碼 快速查看
在線客服 
