江蘇春晨電纜有限公司生產春晨 YCB扁電纜 卷筒扁電纜，壓標準合格率是衡量電能質量的主要指標之一?？墒怯捎诜N種原因，高峰和低谷時期的用電量往往相差懸殊，造成配電變壓器輸出電壓偏低，設備不能用，而電壓的忽高忽低對各種用電設備的性能、生產效率和產品質量都有不同程度的影響，因此，為了確保供電電壓的合格率，及時調節配電變壓器分接開關位置是解決問題的辦法之一。那么如何調變壓器的輸出電壓，變壓器電壓低怎么調高。

The qualified rate of voltage standard is one of the main indexes to measure the power quality. However, due to various reasons, the power consumption in peak and low periods is often quite different, resulting in the low output voltage of distribution transformer and the unavailability of equipment, and the fluctuation of voltage has different degrees of influence on the performance, production efficiency and product quality of various electrical equipment. Therefore, in order to ensure the qualified rate of power supply voltage, adjust the tap changer position of distribution transformer in time Is one of the solutions to the problem. Then how to adjust the output voltage of the transformer, how to adjust the low voltage of the transformer.

電壓自動調壓器

Automatic voltage regulator

我們國家民用變壓器高壓側（一般為10kV）繞組標準設三檔分接開關供調壓；

Our country's civil transformer high voltage side (generally 10kV) winding standard sets three grade tap changer for voltage regulation;

三檔分接開關為：中間檔對應電壓Ue，另二檔對應電壓分別為+5%*Ue、-5%*Ue；

The third gear tap changer is: the middle gear corresponds to the voltage UE, and the second gear corresponds to the voltage ue of + 5% * UE and - 5% * UE respectively;

三檔的繞組匝數是變壓器出廠時固定的：設Ue檔時繞組匝數為Ne，+5%*Ue檔時繞組匝數為N1、-5%*Ue檔時繞組匝數為N2；低壓側繞組匝數N固定不可調。

The winding turns of the third gear are fixed when the transformer leaves the factory: when the UE gear is set, the winding turns are ne; when the + 5% * UE gear is set, the winding turns are N1; when the - 5% * UE gear is set, the winding turns are N2; the winding turns n of the low-voltage side are fixed and not adjustable.

匝數N1大于匝數N2，匝數Ne介于N1與N2間；

Turns N1 is greater than turns N2, and turns ne is between N1 and N2;

變壓器的變比為n=（Ne、N1、N2）/N，n=Ne/N為額定變比；低壓側電壓U2=高壓側U1/n；

The transformation ratio of the transformer is n = (NE, N1, N2) / N, n = Ne / N is the rated transformation ratio; the voltage U2 at the low voltage side is U1 / N at the high voltage side;

U1為系統電壓，我們無法改變；

U1 is the system voltage, which we cannot change;

若U2太低，由U2=U1/n知，我們只需降低n即可；春晨 YCB扁電纜 卷筒扁電纜

If U2 is too low, from U2 = U1 / N, we only need to reduce N;

請看看變壓器分接開關現在在哪檔，從n=（Ne、N1、N2）/N中選擇n稍小的那檔試試，依此類推。

Please see which gear the transformer tap changer is in now, choose the gear with smaller n from n = (NE, N1, N2) / N, and so on.