進口真空蝶閥推薦-德國洛克

一、進口真空蝶閥產品簡介：

德國《LOCKE》洛克進口真空蝶閥適用于電力等行業，介質為蒸汽或空氣的真空管路上，作通流或截止用，是密封型蝶閥，具有嚴密性好、啟閉操作靈活的特點，密封圈采用特種橡膠制成，耐溫高，耐老化性好，使用壽命長。

進口真空蝶閥采用T形斷面的密封圈，適應高速蒸汽介質的工況，調整密封圈的壓緊程度，可獲得最佳密封與操作效果。

Locke imported vacuum butterfly valve is suitable for electric power and other industries. The medium is steam or air on the vacuum pipeline. It is used for flow or cut-off. It is a sealed butterfly valve with good tightness and flexible opening and closing operation. The sealing ring is made of special rubber, with high temperature resistance, good aging resistance and long service life.

The imported vacuum butterfly valve adopts T-shaped section sealing ring, which adapts to the working condition of high-speed steam medium and adjusts the compression degree of sealing ring to obtain the best sealing and operation effect.

二、進口真空蝶閥技術性能：

● 漏率：≤1.3×10-9Pa.M3/S;

● 適用壓力范圍：1.3×10-5Pa～3×105Pa;

● 工作溫度：氟橡膠-25℃～+150℃；

● 安裝位置：任意；

● 閥板兩側壓力差對閥門開、關無關；

● 壽命：≥10000次。

● leakage rate: ≤ 1.3 × 10-9pa.m3/s;

● applicable pressure range: 1.3 × 10-5pa ～ 3 × 105Pa;

● working temperature: Viton - 25 ℃ ~ + 150 ℃;

● installation position: any;

● the pressure difference on both sides of the valve plate has nothing to do with the opening and closing of the valve;

● service life: ≥ 10000 times.

三、進口真空蝶閥技術參數：

1公稱通徑：DN15-600mm

2、公稱壓力：PN1.6-40Mpa

3、適用溫度：-25～150℃

4、閥體：WCB碳鋼，不銹鋼304，不銹鋼316

5、閥座：氟橡膠，丁腈膠

6、適用范圍：水，污水，油品，氣，蒸汽

7、連接方式：對夾，法蘭

8、制造標準：美標，國標，日標等

1. nominal diameter: dn15-600mm

2. Nominal pressure: pn1.6-40mpa

3. Applicable temperature: - 25 ～ 150 ℃

4. Valve body: WCB carbon steel, stainless steel 304, stainless steel 316

5. Seat: Viton, acrylic

6. Scope of application: water, sewage, oil, gas, steam

7. Connection mode: clamp, flange

Manufacturing standard: American Standard, national standard, Japanese standard, etc

四、進口真空蝶閥產品特點： 

1、采用中線式碟板與短結構鋼板焊接的新型結構形式設計制造的，結構緊湊、重量輕、便于安裝、流阻小、流通量大，避免高溫膨脹的影響，操作輕便。

2、內無連桿、螺栓等、工作可靠、使用壽命長?？梢远喙の话惭b，不受介質流向影響。

1. It is designed and manufactured by using the new structural form of the middle line type disc plate welded with the short structural steel plate. It is compact in structure, light in weight, easy to install, small in flow resistance and large in flow volume, avoiding the influence of high temperature expansion, and easy to operate.

 2. There is no connecting rod and bolt inside, which is reliable and long service life. It can be installed in multiple stations, not affected by the flow direction of media.

五、進口真空蝶閥安裝說明：

（1）取掉法蘭端兩邊的保護蓋，在閥完全打開的狀態下進行沖洗清潔。

（2）安裝前應按規定的信號（電動或氣動）進行整機測試（防止因運輸產生振動影響使用性能），合格后方可上線安裝（接線按電動執行機構線路圖）。

（3）準備與管道連接前，須沖洗和清除干凈管道中殘存的雜質（這些物質可能會損壞閥座和球）。

（4）在安裝期間，請不要用閥的執行機構部分作為起重的吊裝點，以避免損壞執行機構及附件。

（5）本類閥應安裝在管道的水平方向或垂直方向。

（6）安裝點附近的管道不可有低垂或者承受外力的現象，可以用管道支架或者支撐物來消除管線的偏離。

（7）與管道連接后，請用規定的扭矩交叉鎖緊法蘭連接螺栓。

(1) Remove the protective covers on both sides of the flange end, and wash and clean when the valve is fully open.

(2) Before installation, the whole machine shall be tested according to the specified signal (electric or pneumatic) (to prevent the vibration caused by transportation from affecting the use performance), and it can be installed online only after it is qualified (the wiring shall be in accordance with the circuit diagram of electric actuator).

(3) Before preparing to connect with the pipe, the residual impurities in the pipe must be washed and removed (these substances may damage the valve seat and ball).

(4) During the installation, please do not use the actuator part of the valve as the lifting point to avoid damaging the actuator and accessories.

(5) This type of valve shall be installed in the horizontal or vertical direction of the pipeline.

(6) The pipeline near the installation point shall not be sagged or bear external force, and the pipeline support or support can be used to eliminate the deviation of the pipeline.

(7) After connecting with the pipeline, please cross lock the flange connecting bolts with the specified torque.