進口熱靜力波紋管式疏水閥產品簡介-德國洛克

一、進口熱靜力波紋管式疏水閥產品簡介：

德國《LOCKE》洛克進口熱靜力波紋管式疏水閥，Thermostatic bellows steam trap，也叫熱靜力波紋管式疏水器，熱靜力波紋管式蒸汽疏水閥，熱靜力波紋管式蒸汽疏水器，根據閥腔內溫度的變化是成波紋管內感溫液體的汽化或冷凝，波紋管的內壓產生變化而驅使波紋管帶動閥芯作移位啟閉閥座孔，達到阻汽排水。該閥能充分利用熱能．特別適用于蒸汽伴熱管線，是低溫排水的環保型現熱疏水閥。

Thermo static bellows steam, Locke, Germany Trap, also known as thermal static bellows type steam trap, thermal static bellows type steam trap, thermal static bellows type steam trap, according to the change of the temperature in the valve chamber is the vaporization or condensation of the temperature sensing liquid in the bellows, and the change of the internal pressure of the bellows drives the bellows to drive the valve core to move to open and close the valve seat hole, so as to prevent the steam and drain. The valve can make full use of the heat energy, especially suitable for the steam tracing pipeline. It is an environmental friendly existing heat drain valve for low-temperature drainage.

二、進口熱靜力波紋管式疏水閥技術參數：

1、產品口徑  DN15～DN500，1/2-20寸

2、公稱壓力  1.6Mpa-50Mpa；150LB-4500LB

3、適用溫度  80-600℃

4、連接方式  螺紋，焊接，法蘭

5、閥體材質  20#﹑1Cr18Ni9Ti﹑304﹑316﹑316L﹑12Cr1Mov等

6、適用介質  蒸汽

7、應用場合  廣泛用于蒸汽主管道，伴熱管線、夾套鍋及各種小型蒸汽設備。

 1. Product caliber: dn15-dn500, 1 / 2-20 inch

2. Nominal pressure: 1.6mpa-50mpa; 150lb-4500lb

3. Applicable temperature 80-600 ℃

4. Connection mode: thread, welding, flange

5. Valve body material: 20 × 10, 1Cr18Ni9Ti, 304, 316, 316L, 12Cr1MoV, etc

6. Applicable medium steam

7. It is widely used in steam main pipe, heat tracing pipe, jacketed pot and various small steam equipment.

主要零件材料

三、進口熱靜力波紋管式疏水閥性能特點：

1，排水溫度可以調節在70-100度之間，使用方便。

2，能夠阻止高溫度凝結水的排放，保持蒸汽管線的熱能。

3，連續排放，沒有噪音。蒸汽壓力的小波動沒有影響使用。

4，結構簡單，安裝方便，隨意。

5，通過增加波紋管直徑提高凝結水的排列量。

6，具有良好的排空性能，不怕凍。零泄漏，背壓率達到75%以上。

1. The drainage temperature can be adjusted between 70-100 degrees, which is convenient to use.

2. It can prevent the discharge of high temperature condensate and maintain the heat energy of steam pipeline.

3. Continuous emission, no noise. The small fluctuation of steam pressure does not affect the use.

4. Simple structure, convenient installation and free.

5. Increase the diameter of bellows to increase the arrangement of condensate.

6. It has good evacuation performance and is not afraid of freezing. Zero leakage, back pressure rate of more than 75%.

四、進口熱靜力波紋管式疏水閥工作原理：

熱靜力型蒸汽疏水閥是靠蒸汽和冷卻的凝結水和空氣之間的溫差來工作的。蒸汽增加熱靜力元件內部的壓力，使疏水閥關閉。凝結水和不凝結氣體在集水管里積存，溫度開始下降，熱靜力元件收縮，打開閥門。

在疏水閥前積存的凝結水量，取決于負荷條件，蒸汽壓力和管道尺寸。值得注意的是，不凝結氣體可能會在凝結水的后面積存。

The thermal static steam trap is operated by the temperature difference between the steam and the cooling condensate and air. The steam increases the pressure inside the thermo static element to close the drain valve. The condensed water and non condensed gas accumulate in the water collecting pipe, the temperature begins to drop, the thermal static components contract, and the valve is opened.

The amount of condensate accumulated in front of the trap depends on the load conditions, steam pressure and pipe size. It should be noted that non condensable gas may accumulate behind the condensate.