Honeywell Analytics  FS7-2173-2RP

物品 ：FS7-2173-2RP

品牌：霍尼韋爾分析

FS7-2173-2RP FS7 多光譜火災和火焰探測器，非閉鎖警報和報警繼電器，Honeywell Analytics 的 Viton O 形圈Fire Sentry FS7-2173 光電輻射能火災探測器 - 和具有多光譜寬帶 IR?、近帶 IR 和可見帶火災探測功能的 Fire Sentry FS7-2173-2RP（組合型號）專為半導體潔凈室而設計防火應用。Fire Sentry FS7 火災探測器提供對半導體濕臺火災的智能兩級響應：第一階段：警報。這是對熱能輸出為 3 kW（相當于直徑 4 英寸的聚丙烯水池火災）的小火的第一階段響應。這使火有時間自熄。階段 2：警報。如果火不能自熄，并增長到工廠互助協會的 13 kW 熱能閾值（相當于 8 英寸直徑的聚丙烯水池火災），則激活第二階段響應。

Fire Sentry FS7-2173 與 Fire Sentry FS7-130-SX 控制器或控制面板 FSWB 一起使用?？刂破骱涂刂泼姘鍨樘綔y器供電，監控所有探測器的狀態，并通過數字 RS-485 通信通道與探測器進行通信。Fire Sentry FS7-2173 配備標準的 20 英尺電纜連接器。探測器使用自鎖連接器和 Fire Sentry 接線盒連接到控制器或控制面板。這允許快速簡單的連接，消除接線問題。每個探測器可以在非易失性存儲器中存儲多達六個時間和日期標記的 FirePics?（事件前多光譜傳感器陣列數據）。控制器和控制面板還可以將事件歷史表存儲在非易失性存儲器中，其中包含帶有時間和日期標記的警報、警報和故障歷史記錄。Fire Sentry FS7-2173-2RP 單元化型號的微處理器采用數字信號處理算法，持續監控電路、傳感器的內置自檢并驗證是否正常運行。帶有離散繼電器輸出的 Fire Sentry FS7-2173-2RP 設計用作獨立探測器并與任何經批準的火警面板接口。探測器需要一個外部 24 VDC 電源，并配有標準的 20 英尺尾纖電纜。它可以在非易失性存儲器中存儲多達六個時間和日期標記的 FirePics? 和 200 個事件。FirePics? 和事件歷史可以使用 Fire Sentry FS7 接口套件和 Fire Sentry 基于 Windows 的 PC 軟件進行檢索。特征：多光譜數字光電輻射能紅外火災探測器獨特的兩級火災探測響應免疫誤報源不受吸收煙霧、氣體或化學蒸氣的影響對來自電加熱器和烤箱的背景輻射能量不檢測碳氫化合物和非碳氫化合物火災堅固的防漏、熱密封、耐酸、注塑聚丙烯外殼120° 寬視野帶RS-485接口的數字通訊FirePic?；帶有時間和日期戳的數字火災簽名內置探測器自動自檢單機操作的單元化模型設計

應用包括：潔凈室的開放區域濕臺工作面濕臺面地下（壓力通風系統）位于濕臺區后面的泵和設備地板下區域IPA 工作站（僅限組合型號）

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR?, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics? (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics? and event histories can be retrieved from the controller or control panel.Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics? and 200 events in non-volatile memory. FirePics? and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.