PFM-711B 靜電場計

手持式場計定位和測量靜電場密度

★輕便、便攜、手持式現場測量儀

★以 1 伏特/增量 0 至 ±1,999 伏特進行測量

★以 10 V/in 增量測量 0 至 ±20,000 V

★<±5% 的準確度

★LED 測距燈有助于將儀表定位在正確的距離

★歸零按鈕允許將顯示調整為零 (0)

★保持功能在顯示屏上凍結測量

★與 Prostat CPM-720B 充電板監視器和 PCS-730B 靜電充電器一起使用

★與 Prostat PGA-710B 自動分析系統或 XY 繪圖儀一起使用

★分析鞋類/地板組合

★驗證離子發生器平衡和衰減時間性能

★2 年有限保修（傳感器 1 年）

使用斬波穩定傳感器

PFM-711B 是一款精確的便攜式靜電場測量設備，易于使用，專為單手操作而設計。PFM-711B 是一種數字電子斬波器設計，允許儀器在存在電離空氣的區域進行靜電場測量。PFM-711B 單獨使用時，幾乎可以測量任何平面或物體發出的靜電場。

以 1 伏和 10 伏為增量

進行測量 PFM-711B 使用雙量程來測量正極和負極電荷的表面電壓和靜電勢。在 kV/Inch 范圍內，PFM-711B 將在距離帶電表面 1" (25mm) 處以 10 伏的增量指示從 0 到 ±20,000 伏的靜電場電壓。在 V/英寸范圍內，場計測量場在距離帶電表面 1" (25mm) 處，密度從 0 到 ±1,999 伏，增量為 1 伏。該儀器易于使用，其控制裝置專為單手操作而設計。

提供接地參考

PFM-711B 場計外殼是導電的。它為其測量電路提供接地參考。為獲得準確的測量結果，手持儀表的人員必須正確接地，或者儀表與安裝在外殼背面的 10 毫米按扣進行接地連接。通過佩戴正確接地的功能性腕帶將外殼接地。打開儀表并選擇所需的范圍。按下 ZERO 控件將顯示調整為零 (0) 伏。

用于精確測量的靶心

測距燈有助于定位儀器以進行精確測量。將 PFM-711B 場強計的前傳感器與被測表面或物體大約 1" (25mm) 對齊。將儀器移向或遠離表面，直到測距燈聚焦在測試表面上。一旦場強計正確放置后，PFM-711B 將在其顯示屏上顯示測得的靜電場。

與記錄設備一起

使用 PFM-711B 是 ESD 控制市場中最靈活的現場儀表。結合各種附件，它可以執行許多不同的測量來分析靜態敏感過程或環境。模擬輸出與 XY 繪圖儀、模擬數據記錄設備或 Prostat PGA-710B 自動分析系統結合使用時可以記錄測量結果. （不包括錄音設備和電纜。）

持久耐用的電池

PFM-711B 使用 9 伏堿性電池（隨附），可提供大約 30 小時的使用壽命。顯示屏旨在指示電池電量不足時。低電量指示器可方便地編程為 7.2 直流電壓，這是準確測量所需的最低電壓。

PFM-711B Electrostatic Field Meter

HAND HELD FIELD METER LOCATES AND MEASURES ELECTROSTATIC FIELD DENSITY

●Lightweight, portable, hand-held Field Meter

●Measure in 1 volt/in increments 0 to ±1,999 Volts

●Measure in 10 V/in increments 0 to ±20,000 Volts

●Accuracy of <±5%

●LED ranging lights help position the meter at the right distance

●Zero button allows the display to be adjusted to zero (0)

●Hold feature freezes the measurement on the display

●Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger

●Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter

●Analyze Footwear/Flooring Combinations

●Verify Ionizer Balance and Decay Time Performance

●2-year Limited Warranty (1 year on the sensor)

Product Overview：

Uses a Chopper-Stabilized Sensor

The PFM-711B is an accurate, portable electrostatic field measuring device that is easy to use and designed for one hand operation. The PFM-711B is a digital, electronic chopper design, which allows the instrument to make electrostatic field measurements in areas where ionized air is present. Used by itself, the PFM-711B will measure electrostatic fields emanating from virtually any flat surface or object.

Measure in 1 Volt and 10 Volt Increments

The PFM-711B uses a dual range for measuring surface voltage and electrostatic potentials in both positive and negative polarity charges. In the kV/Inch range, the PFM-711B will indicate electrostatic field voltage from 0 to ±20,000 volts in 10 volt increments at 1" (25mm) distance from the charged surface. In the V/Inch range, the field meter measures field density from 0 to ±1,999 volts in 1 volt increments at 1" (25mm) distance from the charged surface. The instrument is easy to use and its controls are designed for one hand operation.

Provides a Ground Reference

The PFM-711B Fieldmeter case is conductive. It provides the ground reference for its measuring circuit. For accurate measurements, it is necessary that the person holding the meter be properly grounded, or the meter has a ground connection made to the 10 mm snap fastener mounted on back of case. Ground the case by wearing a functional wrist strap that is properly grounded. Turn the meter on and select the desired range. Adjust the display to zero (0) volts by pressing the ZERO control.

Bulls Eye for Accurate Measurements

The ranging lights help position the instrument for accurate measurements. Align the front sensor of the PFM-711B Field Meter approximately 1" (25mm) from the surface or object being measured. Move the instrument toward, or away from the surface until the ranging lights are focused on the test surface. Once the field meter is properly positioned, the PFM-711B will indicate the electrostatic field measured on its display.

Use it with a Recording Device

The PFM-711B is the most flexible field meter in the ESD control marketplace. Combined with a variety of accessories, it can perform many different measurements to analyze the static sensitive process or environment.The analog output allows documentation of measurements when used in conjunction with X-Y plotter, analog data recording device, or the Prostat PGA-710B Autoanalysis System. (Recording device and cable not included.)

Long Lasting Battery

The PFM-711B uses a 9 volt alkaline battery (included), which provides an approximate life of 30 hours. The display is designed to indicate when the battery is low. The low battery indicator is conveniently programmed to come in at 7.2 DC volts, which is the minimum voltage required for accurate measurements.