產品規格型號：CR2032-BS-2-1
產品顏色：黑色塑膠   
插件類型：DIP
材質：PBT ，Cu&SPCC  
標準箱參考參數：3000只；NW 4.5KGS；GW 6.4KGS   44*29.5*33CM

?適用于扣式電池CR2032/LIR2032,ML2032,BR2032 
?非常便于扣式電池的放入和取出，導通性能優良
?可以提供SGS檢測報告，符合環保要求 

●Battery Precautions for Mounting （電池安裝注意事項）

Unlike other electronic components, Lithium Manganese Dioxide Battery(Coin-type) may be externally short-circuited before and after it is installed in circuit boards and without the power being turned on. This causes power drainage. As a result, the battery may lose its capacity before the equipment is even used. As short-circuits tend to occur in the following cases, please take care when handling the battery.

（不同其它電子零件，鋰-二氧化錳電池（扣式）在安裝到電路板前后可能會外部短路，同時動力未開啟。這會造成動力流失。因此，甚至在設備使用之前電池就可能會損失它的容量。例如短路發生在以下情況下，請謹慎操作電池）

1. Overlapping Batteries （重疊電池）

Lithium Manganese Dioxide Battery is shaped as shown below. It has exposed positive(+)and negative(-) metallic surfaces with a thin cylindrical seal, called the gasket, inbetween them. When the batteries are overlapped or mixed together in a disorderly way, their positive(+)and negative(-)terminals touch each other, causing short-circuits.（鋰-二氧化錳電池形狀如下所示。它敞開的正極與負極間僅僅由一圈很窄的環狀（密封圈）相隔離，當電池雜亂地重疊堆放時，它們的正極 (+)和負極(-)端會相互接觸而造成短路）

2. The Batteries Put in a Metallic Container or on a Metallic Plate

（將電池放入金屬容器或金屬盤里）

Similar to the overlapping battery problem, when the batteries are put in a metallic container or on a metallic plate, their positive(+)and negative(-)terminals may short-circuit through the conductive surface, depending on how the batteries are position.

（與重疊電池問題相似，當電池放到金屬容器或金屬盤里，它們的正極 (+)和負極(-)端可能會通過導電性的表面和電池的位置而造成短路）

3. When The Battery is Held with Metallic Tweezers （當用金屬鑷子夾電池時）

When held with a pair of metallic tweezers as shown, the battery short-circuits through the tweezers.（當用一副金屬鑷子夾電池時，電池通過金屬鑷子短路）

4.  When The Battery Lead Plates Touch Each Other （當電池引線相互接觸時）

When the battery lead plates bend and touch each other or other either terminal, the battery short-circuits.（當電池引線彎曲并相互接觸或其它接線端接觸時，電池短路）

5. Solder Bridges （焊橋）

Solder may bridge between circuit board conductors, causing a short-circuit and draining the battery.（焊接可能橋連電路板導體，造成短路，耗盡電池）

6. Short-circuits through Soldering Irons （通過烙鐵短路）

Similar to solder bridging, when the circuit board wiring is short-circuited by a soldering iron for an extended period the battery is drained and consumed. Complete short-circuits through soldering irons within 5 seconds.（與焊橋相似，當電路板線路被烙鐵超時接觸時引起短路，電池能量將會流失并耗盡。通過烙鐵短路應在5秒內結束）

7. Short-circuits through Piled Circuit Boards （通過堆疊的電路板短路）

When circuit boards with the batteries are piled on top of one another, their conductive traces may touch and form a battery discharge circuit that consumes the battery's power.

（當加載電池的電路板相互堆疊，它們導電性的線路會接觸而形成電池放電電路消耗電池能量）