農田水利U型槽模具   河北宏旭模具

         農田水利U型槽模具  水利U型槽模具主要用于鐵路，高鐵，城際鐵路的路基，站臺電纜方面。從2008年高鐵的普及之后高鐵的大大小小工程接踵而來，高鐵兩側的電纜槽主要采用混凝土預制而成的，鐵路線路有多長，兩側的電纜就需要有多長，所以電纜槽工程量也是相當大的。農田水利U型槽模具  水利U型槽模具的預制混凝土要求比較嚴格一般需要達到c40混凝土，必須保證工程的結實程度。農田水利U型槽模具  水利U型槽模具具一般有兩種材質可以選擇，abs樹脂，4mm鋼板。常用規格主要用ABS因?yàn)樗芰系囊阋撕芏?，非常?guī)的主要采用鋼模板，鋼模板的優勢主要體現在它的穩固耐用上面。澆注系統：將塑料由少射機噴嘴引向型腔的流道稱為澆注系統,由主流道，分流道，澆口。熱交換系統：為了滿足注射成形工藝對模具溫度的要求需要對模具溫度進行較的控制。頂出系統：實現塑膠產品脫模的機構，其結構形式很多，常用的是頂針、司筒和推板等脫模機構。排氣系統：將型腔內空氣導出的結構，如：排氣槽及鑲件配合時的間隙。Farmland water conservancy U-groove mould water conservancy U-groove mould is mainly used for Subgrade and platform cable of railway, high-speed railway and intercity railway. Since the popularity of high-speed rail in 2008, large and small projects of high-speed rail have followed. The cable trays on both sides of high-speed rail are mainly prefabricated with concrete. The length of the railway line depends on the length of the cables on both sides, so the quantities of cable trays are also quite large. The precast concrete requirements of U-groove mould for farmland and water conservancy are relatively strict. Generally, it needs to reach C40 concrete, and the firmness of the project must be guaranteed. Farmland water conservancy U-groove mould water conservancy U-groove mould generally has two materials to choose from, ABS resin and 4mm steel plate. Common specifications mainly use ABS, because plastic is much cheaper. Unconventional ones mainly use steel formwork. The advantages of steel formwork are mainly reflected in its stability and durability. Gating system: the flow channel that leads the plastic from the nozzle of the less ejector to the cavity is called the gating system, which consists of the main flow channel, shunt channel and gate. Heat exchange system: in order to meet the requirements of injection molding process for mold temperature, it is necessary to control the mold temperature. Ejector system: it is a mechanism for demoulding plastic products. It has many structural forms. Commonly used demoulding mechanisms are ejector pin, cylinder and push plate. Exhaust system: the structure that leads the air in the cavity, such as the clearance when the exhaust slot and insert are matched.