進口泄氮閥產品列表德國洛克

一、進口泄氮閥產品描述：

德國LOCKE洛克進口泄氮閥是自主開發、研制的一套自力式微壓力控制系統，主要用于保持容器頂部保護氣(一般為氮氣)的壓力恒定，以避免容器內物料與空氣直接接觸，防止物料揮發、被氧化，以及容器的安全。特別適用于各類大型儲罐的氣封保護系統。

該產品具有節能、動作靈敏、運行可靠、操作與維護方便等特點。廣泛應用于石油、化工等行業。

Locke nitrogen relief valve imported from Germany is a set of self operated micro pressure control system independently developed and developed. It is mainly used to keep the pressure of protective gas (generally nitrogen) at the top of the container constant, so as to avoid direct contact between materials in the container and air, prevent volatilization and oxidation of materials, and ensure the safety of the container. It is especially suitable for gas seal protection system of various large storage tanks.

The product has the characteristics of energy saving, sensitive action, reliable operation, convenient operation and maintenance. It is widely used in petroleum, chemical and other industries.

二 、進口泄氮閥技術參數：

Nominal diameter: DN 10-dn 100

Nominal pressure: PN16, PN25 or ansi150lb

Flow characteristics: quick opening

Pressure regulation range (kPa): 0.4-5.5, 5-10, 9-14, 13-19, 18-24, 22-28, 27-33, 31-38, 36-44, 42-51, 49-58, 56-66

Medium temperature (℃) ≤ 80

Adjustment accuracy (%) ≤ 5%

Allowable leakage level standard level: grade IV (GB / t4213-92) tight type: grade VI (GB / t4213-92)

Materials of main parts and components:

Valve body: zg230-450, zg1cr18ni9ti

Valve internals: 1Cr18Ni9Ti

Diaphragm cover: A3, 1Cr18Ni9Ti

Diaphragm: reinforced polyester fabric rubber, fluororubber

Spring: 60Si2Mn, 1Cr18Ni9Ti

According to the user's requirements, the valve body, valve internals and diaphragm cover can be made of other brands.

Connection size and standard

Connection method: flange, thread and welding

Flange end face distance: gb12221-89

Flange standard: GB / t9113-2000

Flange type: RF

Pneumatic signal interface of actuator: M16 × 1.5

Note: the above data can be processed and manufactured according to the needs of users.

三、進口泄氮閥主要特點：

1、無需外加能源，能在無電、無氣的場合工作，既方便又節約能源，降低成本。

2、氮封裝置供氮，泄氮壓力設定方便，可在連續經營的條件下進行。

3、壓力檢測膜片有效面積大，設定彈簧剛度小、動作靈敏、裝置工作平衡。

4、采用無填料設計，閥桿所受磨擦力小、反應迅速、控制精度高。

5、供氮裝置采用指揮器操作，減壓比可達100:1，減壓效果好、控制精度高。

6、為確保儲罐的安全，需在罐頂設置呼吸閥。

7、呼吸閥公起安全作用，避免了常規氮封裝置中啟閉頻繁易損壞的缺陷。

1. Without additional energy, it can work without electricity and gas, which is convenient, energy saving and cost reducing.

2. The nitrogen sealing device can supply nitrogen and discharge nitrogen pressure conveniently, which can be carried out under the condition of continuous operation.

3. The pressure detection diaphragm has large effective area, small stiffness of setting spring, sensitive action and balance of device.

4. The non packing design makes the valve stem less friction force, quick response and high control precision.

5. The nitrogen supply device is operated by the director, the decompression ratio can reach 100:1, the decompression effect is good and the control precision is high.

6. In order to ensure the safety of the storage tank, it is necessary to set a breathing valve on the top of the tank.

7. The breathing valve is safe to avoid the defect of frequent opening and closing in the conventional nitrogen sealing device.

四、進口泄氮閥工作原理：

供氮裝置，將設在罐頂?shù)娜狐c的介質經導壓管引入檢測機構，介質在檢測元件上產生一個作用力與與彈簧、預緊力相平衡。當罐內壓力降低至低于供氮裝置壓力設定點時，平衡破壞，使指揮器閥芯，打開，使閥前氣體經減壓閥，節流閥、進入主閥執行機構上、下膜室，打開主閥閥芯，向罐內充注氮氣；當罐內壓力升至供氮裝置壓力設定點，由于預設彈簧力，關閉指揮器閥芯、由于主閥執行機構中的彈簧作用，關閉主閥，停止供氮。

泄氮裝置，該裝置采用內反饋結構，介質直接經閥蓋進入檢測機構，介質在檢測元件上產生一個作用力與預設彈簧、預緊力相平衡。當罐內壓力升高至高于泄氮裝置壓力設定點時，平衡被破壞，使閥芯上移，打開閥門，向外界泄放氮氣；當罐內壓力降至泄氮裝置壓力設定點，由于預設彈簧力作用，關閉閥門。

因微壓調節閥必須使用在壓力為0.1Mpa壓力以下，現場壓力較高，必須安裝壓力調節閥將壓力調節閥將壓力降低至0.1Mpa以下才可使用。氮封閥公稱壓力都為0.1Mpa，壓力可按分段設定，從0.5Kpa至66 Kpa以下，介質溫度溫度≤80℃。

In the nitrogen supply device, the medium at the pressure measuring point on the top of the tank is introduced into the detection mechanism through the pressure pipe. A force generated by the medium on the detection element is balanced with the spring and preload force. When the pressure in the tank is lower than the pressure set point of the nitrogen supply device, the balance is broken, and the valve core of the command device is opened, so that the gas in front of the valve enters the upper and lower membrane chambers of the main valve actuator through the pressure reducing valve and throttle valve, and then the main valve is filled with nitrogen by opening the valve core of the main valve; when the pressure in the tank rises to the pressure setting point of the nitrogen supply device, the valve core of the command device is closed due to the preset spring force The spring action in the actuator closes the main valve and stops nitrogen supply.

The device adopts an internal feedback structure, and the medium directly enters the detection mechanism through the valve cover. The medium generates a force on the detection element to balance with the preset spring and pre tightening force. When the pressure in the tank is higher than the pressure set point of the nitrogen relief device, the balance is destroyed, which makes the valve core move upward, open the valve and release nitrogen to the outside; when the pressure in the tank drops to the pressure set point of the nitrogen relief device, the valve is closed due to the preset spring force.

Because the micro pressure regulating valve must be used under the pressure of 0.1MPa and the field pressure is high, the pressure regulating valve must be installed to reduce the pressure to below 0.1MPa before it can be used. The nominal pressure of nitrogen seal valve is 0.1MPa, the pressure can be set in sections, from 0.5kpa to below 66kpa, and the medium temperature is ≤ 80 ℃.