按需定制 扭王字塊模具 樂豐扭王字塊模具 設計制作

扭王字塊模具都是用于預制生產，一次就會產出幾十個預制件，所以為防止在注入混凝土后漏漿，可有選擇使用電動扳手來擰模具的螺栓，省力又可以保障生產質量。在拼接好的模具內均勻地刷上一層脫模劑后就可以澆筑混凝土了，注意使用的混凝土需要提前使用混凝土攪拌機按照規定的比例進行配比并攪拌均勻。注漿后需要使用振動棒勻速攪拌混凝土泥漿，這個步驟對于梯形水溝預制件的生產制作而言是十分重要的，因為如果震動不充分在預制件內部留有氣泡，導致其表面形成一層密密麻麻的蜂窩狀孔洞，十分影響美觀，同時還會導致梯形水溝抗壓能力不足，容易坍塌，震動后就可以直接等待其完全凝固，拆除梯形水溝模具了。

In order to prevent slurry leakage after concrete injection, we can choose to use electric wrench to screw the bolts of the mold, which can save labor and guarantee the production quality. After evenly brushing a layer of release agent in the spliced mold, the concrete can be poured. Note that the concrete to be used needs to be proportioned in advance with a concrete mixer according to the specified proportion and mixed evenly. After grouting, it is necessary to mix the concrete slurry at a constant speed with a vibrating rod. This step is very important for the production and manufacture of the prefabricated parts of the trapezoidal ditch. If the vibration is not sufficient, there will be bubbles inside the prefabricated parts, resulting in a layer of dense honeycomb holes on the surface of the prefabricated parts, which greatly affects the appearance, and at the same time, it will lead to the insufficient compressive capacity of the trapezoidal ditch and easy to collapse, After shaking, we can wait for it to solidify completely and remove the trapezoid ditch mold.

扭王字塊模具在加工制作完成以后需要使用合理的手段來養護模具，避免模具過早的老化，能夠有效延長鋼模具的使用壽命，鋼模具的保養方式與塑料模具是有所不同的，這是由它的材質決定的，首先，遮板鋼模具在周期使用之后需要磨刃口，否則容易出現混凝土料堵口的狀況，我們要每天對模具的狀況進行記錄，詳細記載它的使用狀況以及養護情況；其次，我們在發現模具的組件或者零件有損壞的時候就要進行及時處理，將能夠更換的零件進行更換，不能更換的就要進行修補，保證模具能夠在正常運轉狀態下進行生產；再次要注意遮板鋼模具的磨損程度，找到模具的型腔和分型面的損壞位置，對其進行維修，而作為在預制過程當中比較容易被損壞的彈簧，我們要提前準備好備用的零件，使用同樣的規格和尺寸進行更換。

After the completion of the processing and manufacturing of the twist Wang block mold, it is necessary to use reasonable means to maintain the mold to avoid premature aging of the mold, which can effectively extend the service life of the steel mold. The maintenance mode of the steel mold is different from that of the plastic mold, which is determined by its material. First, the shutter steel mold needs to be sharpened after the cycle use, otherwise the concrete is easy to appear For the condition of material plugging, we need to record the condition of the mold every day, and record its use condition and maintenance condition in detail; secondly, we need to deal with it in time when we find the components or parts of the mold are damaged, replace the parts that can be replaced, and repair the parts that can not be replaced, so as to ensure that the mold can be produced in normal operation; Again, pay attention to the wear degree of the shutter steel mold, find out the damaged position of the mold cavity and parting surface, and repair them. As a spring that is easy to be damaged in the prefabrication process, we should prepare spare parts in advance, and use the same specification and size for replacement.