德國洛克進口電動減壓閥工作穩定可靠經久耐用

一、進口電動減壓閥結構特點和用處：   

本系列減壓閥主要由閥體、閥座、閥瓣等零件組成，采用雙閥座、雙錐體閥瓣的結構。采用壓力平衡式閥瓣，通過閥瓣升降調節壓力可配用BC型或其它型直行程電動執行器實現遙控和自動控制。   

本系列產品的減壓比用到0.6較為合適。   

本產品主要用于蒸汽管路，調節壓力。廣泛應用在熱電聯產、輕紡、印染、石化、制糖等行業。

This series of pressure reducing valve is mainly composed of valve body, valve seat, valve disc and other parts, and adopts the structure of double valve seat and double cone valve disc. The pressure balanced valve disc is adopted, and the pressure can be adjusted by lifting the valve disc, and the BC type or other types of direct stroke electric actuators can be used to realize remote control and automatic control.

The decompression ratio of this series of products is 0.6.

This product is mainly used for steam pipeline and pressure regulation. Widely used in cogeneration, textile, printing and dyeing, petrochemical, sugar and other industries.

二、進口電動減壓閥描述：

德國LOCKE洛克進口電動減壓閥由直行程電子式電動執行機構和直通單座閥組成。內含飼服功能，接受統一的4-20mA或1-5V·DC的標準信號，將電流信號轉變成相對應的直線位移，自動地控制調節閥開度，達到對管道內流體的壓力的連續調節。當管道壓力很高，或者要求降壓幅度較大的減壓場合，不可用自力式減壓閥，必須采用電動減壓閥，電動減壓閥進口適用于對泄露量要求嚴格、閥前后壓差低及有一定粘度和含少量纖維介質的場合。

The electric pressure reducing valve imported from Locke lock, Germany, is composed of a straight stroke electronic electric actuator and a straight through single seat valve. It contains feeding function, accepts unified standard signal of 4-20mA or 1-5V · DC, transforms current signal into corresponding linear displacement, and automatically controls the opening of regulating valve to achieve continuous regulation of fluid pressure in the pipeline. When the pipeline pressure is very high or the pressure reduction range is required to be large, the self operated pressure reducing valve cannot be used. The electric pressure reducing valve must be used. The inlet of the electric pressure reducing valve is suitable for the field with strict requirements on leakage, low pressure difference between the front and back of the valve, certain viscosity and a small amount of fiber medium.

三、進口電動減壓閥技術參數:

1、型    式：直通單座鑄造球型閥

2、公稱通徑：DN20-200mm

3、公稱壓力：PN1.6-16Mpa 1500Lb，2500Lb

4、法蘭標準：ANSI B16.5   JB/T79.1-94、79.2-94等

5、材    料：鑄鋼（ZG230-450）、鑄不銹鋼（ZGlCrl8Ni9Ti、ZGlCrl8Nil2Mo2Ti）等

6、上 閥 蓋：標準型-17～+230℃、散熱型+230～+450℃、低溫型-60～-196℃、波紋管密封-40～+350℃

7、壓蓋型式：螺栓壓緊式

8、填    料：V型聚四氟乙烯填料、含浸四氟乙烯石棉填料、石棉編織填料、石墨填料

1. Type: straight through single seat cast ball valve

2. Nominal diameter: dn20-200mm

3. Nominal pressure: pn1.6-16mpa 1500Lb, 2500lb

4. Flange standard: ANSI B16.5 JB / t79.1-94, 79.2-94, etc

5. Materials: cast steel (zg230-450), cast stainless steel (zglcrl8ni9ti, zglcrl8nil2mo2ti), etc

6. Upper valve cover: standard type - 17 ～ + 230 ℃, heat dissipating type + 230 ～ + 450 ℃, low temperature type - 60 ～ - 196 ℃, bellows seal - 40 ～ + 350 ℃

7. Gland type: bolt compression type

8. Packing: V-type polytetrafluoroethylene packing, containing PTFE asbestos packing, asbestos woven packing, graphite packing

四、進口電動減壓閥工作原理及應用：

進口減壓閥工作原理是電動調節閥在壓力控制領域的典型應用。電動減壓閥通過調節一次側流體的動壓頭，達到控制減壓閥后壓力的目的。本類閥門在管道中一般應當水平安裝。適用于對泄露量要求嚴格、閥前后壓差低及有一定粘度和含少量纖維介質的場合。

The working principle of imported pressure reducing valve is a typical application of electric control valve in the field of pressure control. The electric pressure reducing valve controls the pressure behind the pressure reducing valve by adjusting the dynamic head of the primary side fluid. This kind of valve should be installed horizontally in the pipeline. It is suitable for occasions with strict requirements on leakage, low pressure difference between front and back of valve, certain viscosity and a small amount of fiber medium.