YSX321SL 3225 4P 請點擊您需要的參數一起加到購物車,找不到您需要的請聯系客服 標準頻率 負載電容 頻率偏差 點擊購買 12MHZ 10PF 10PPM rel="nofollow" Buy 12MHZ 12PF 10PPM rel="nofollow" Buy 12MHZ 20PF 10PPM rel="nofollow" Buy 14.7456MHZ 12PF 10PPM rel="nofollow" Buy 16MHZ 18PF 10PPM rel="nofollow" Buy 20MHZ 20PF 10PPM rel="nofollow" Buy 24MHZ 10PF 10PPM rel="nofollow" Buy 24MHZ 12PF 10PPM rel="nofollow" Buy 24MHZ 20PF 20PPM rel="nofollow" Buy 25MHZ 10PF 10PPM rel="nofollow" Buy 25MHZ 12PF 10PPM rel="nofollow" Buy 25MHZ 20PF 10PPM rel="nofollow" Buy 26MHZ 9PF 10PPM rel="nofollow" Buy 26MHZ 10PF 10PPM rel="nofollow" Buy 26MHZ 12PF 10PPM rel="nofollow" Buy 27MHZ 20PF 10PPM rel="nofollow" Buy 27.12MHZ 10PF 10PPM rel="nofollow" Buy 30MHZ 12PF 10PPM rel="nofollow" Buy 30MHZ 20PF 10PPM rel="nofollow" Buy 48MHZ 20PF 10PPM rel="nofollow" Buy 54MHZ 10PF 10PPM rel="nofollow" Buy 如您需要購買同類別的其他系列產品，請點擊以下鏈接 產品型號 產品規格 點擊購買 HC-49US 11.5x4.5x3.68mm rel="nofollow" Buy HC-49SMD 11.4x4.8x3.8mm rel="nofollow" Buy HC-49UM 11.05x4.65x13.46mm rel="nofollow" Buy YSX321SL 3225 4P rel="nofollow" Buy YSX530GA 5032 2P rel="nofollow" Buy YSX531SL 5032 4P rel="nofollow" Buy YT-26 2060 2P rel="nofollow" Buy YT-38 3080 2P rel="nofollow" Buy R315 D11,F11,TO39 rel="nofollow" Buy R433 D11,F11,TO39 rel="nofollow" Buy 石英晶振壓封條件 影響石英晶振平行封焊的因素還有夾具的設計、電極的位置、上蓋的質量和上蓋與基座的匹配等，另外封焊設備本身的可靠性也是影響封焊質量的因素之一。 夾具孔位的中心與轉臺中心要一致，夾具夾牢基座，否則焊接過程中電極可能會把基座粘起來；左、右電極位置保持在同一高度和同一水平線上且盡量對稱；電極滾輪要定期打磨和更換、否則會影響焊接均勻性；上蓋尺寸不能太大或太小，而且拐角有傾角，因?yàn)殚L(zhǎng)方形基座的焊接電極與上蓋角接觸兩次，焊接熱量會影響焊接效果；采用邊緣有傾角的上蓋，焊接時錯位的可能性會大大減小。 工藝參數的設定要根據各公司的現狀而定，只有優化工藝參數，才能提高石英晶振焊接質量。在石英晶振封焊完產品后，對封裝過程中出現的現象進行適當?shù)目偨Y(jié)，有待封裝技術的進一步提高。 真空平行縫焊（真空度在無負載、無封焊動作時可達1.1×10-3Pa），是在短邊封焊時加一道抽真空（真空度可達5×10-2Pa），后再封焊，其結果能大大的改善晶體的電阻指標（可下降30~50%），適用于小尺寸、高指標的產品。 平行封焊有半自動機，只完成上蓋點焊；滾焊密封由另一臺設備完成，中間銜接有人工搬運。全自動機是將真空烘烤、上蓋、點焊，滾焊密封、收納一機完成。